First flight CAN, DIMU no Cal = WOW!!!

Info & Discussions about good ole AQ6, taken to the next level.

Re: First flight CAN, DIMU no Cal = WOW!!!

Postby kinderkram » Thu May 08, 2014 12:02 am

Thx fort sharing, James!

Looks pretty fit & tough. Congratz for the first documented speed record 2014 of 54mph! :lol:


P.S.: I`ve edited your post so your video shows up.
You only need to paste the YT video ID (in your case 7WOLHh2-4IU) between the YT tags:

Code: Select all
[youtube]7WOLHh2-4IU[/youtube]
kinderkram
 
Posts: 2911
Joined: Fri Jun 22, 2012 7:47 am

Re: First flight CAN, DIMU no Cal = WOW!!!

Postby Jdmagoo » Thu May 08, 2014 12:04 am

kinderkram wrote:Thx fort sharing, James!

Looks pretty fit & tough. Congratz for the first documented speed record 2014 of 54mph! :lol:


P.S.: I`ve edited your post so your video shows up.
You only need to paste the YT video ID (in your case 7WOLHh2-4IU) between the YT tags:

Code: Select all
[youtube]7WOLHh2-4IU[/youtube]


Oh thanks for that, will do for the next vid.

James
Jdmagoo
 
Posts: 485
Joined: Sun Feb 17, 2013 8:35 am

Re: First flight CAN, DIMU no Cal = WOW!!!

Postby joebar.rc » Thu May 08, 2014 7:23 am

Jdmagoo wrote:
The precision of autoquad and DIMU rocks. All this with no cal only the Tare.

If interested, best to watch in a minimum of 720p

James

Great fast vid James :)
Regarding the tilt of the gimbal, that would be the point of interest setting.
Good to remind me, did you use the wp recording for that, because if you did I will check that I also create a neutral poi so that will be prevented.

It does however only occur if you get AQ to set the tilt, if you use a pass through port with tpa passthrough channel AQ will not control it, only you.
Anyways, something to check :)
joebar.rc
 
Posts: 1084
Joined: Fri Jun 22, 2012 8:59 am
Location: The netherlands

Re: First flight CAN, DIMU no Cal = WOW!!!

Postby aBUGSworstnightmare » Thu May 08, 2014 9:43 am

Hi James,

WOW! Impressive performance! Would bei nice if you could share some details of your setup and some pictures of your craft.

Joerg
aBUGSworstnightmare
 
Posts: 1460
Joined: Fri Jun 22, 2012 5:24 pm

Re: First flight CAN, DIMU no Cal = WOW!!!

Postby JussiH » Thu May 08, 2014 11:21 am

James,

Im totally pleased to see you having success with AQ. Nice craft, flies very well! Well done :)
JussiH
 
Posts: 2103
Joined: Thu Jun 21, 2012 9:25 pm

Re: First flight CAN, DIMU no Cal = WOW!!!

Postby Jdmagoo » Sat May 10, 2014 6:18 am

joebar.rc wrote:
Jdmagoo wrote:
The precision of autoquad and DIMU rocks. All this with no cal only the Tare.

If interested, best to watch in a minimum of 720p

James

Great fast vid James :)
Regarding the tilt of the gimbal, that would be the point of interest setting.
Good to remind me, did you use the wp recording for that, because if you did I will check that I also create a neutral poi so that will be prevented.

It does however only occur if you get AQ to set the tilt, if you use a pass through port with tpa passthrough channel AQ will not control it, only you.
Anyways, something to check :)


Yeah i did use the POI for that, i recorded 3 POI's and the camera tilted up between two of them but on the last leg it was fine.
Jdmagoo
 
Posts: 485
Joined: Sun Feb 17, 2013 8:35 am

Re: First flight CAN, DIMU no Cal = WOW!!!

Postby Jdmagoo » Sat May 10, 2014 6:21 am

aBUGSworstnightmare wrote:Hi James,

WOW! Impressive performance! Would bei nice if you could share some details of your setup and some pictures of your craft.

Joerg


Frame: Flyduino FCP-HL - Hexa
FC: Autoquad with DIMU upgrade
Motors: T-Motor MN3110-17 700Kv
ESC: ESC32 using CAN bus (no more PWM yay!!)
Props: T-Motor 12x4
Batteries: Thunder Power 5400mah 4S x 2
Flight Time: 13mins
AUW: 3.7kgs (including Gopro Gimbal)
Mav2Hott LED's
AQ FW: R380 Menno's Mav Modified
ESC32 FW: R54

Still to install....

Telemetry: RFD900
OSD: MinimOSD
Video Tx: Lawmate 1.2Ghz

Autoquad.jpg
Autoquad.jpg (1.12 MiB) Viewed 2983 times
Jdmagoo
 
Posts: 485
Joined: Sun Feb 17, 2013 8:35 am

Previous

Return to AQ6 +DIMU +CAN

Who is online

Users browsing this forum: No registered users and 1 guest

cron