I'm set the start voltage to 3 V (max ?) and the start align voltage to 2.4 V. Now it's better , but not solved. In AQ misc. settings, the Min PWM is 1220 and Motor start PWM is 1220...
Motor / Propeller Problem
31 posts
• Page 2 of 4 • 1, 2, 3, 4
Re: Motor / Propeller Problem
by chschmid » Fri Dec 04, 2015 10:17 pm
- chschmid
- Posts: 1800
- Joined: Wed Jul 11, 2012 7:41 pm
- Location: Herrliberg, Switzerland
Re: Motor / Propeller Problem
by Luxar » Sat Dec 05, 2015 8:36 am
Thanks
I'm set the start voltage to 3 V (max ?) and the start align voltage to 2.4 V. Now it's better , but not solved. In AQ misc. settings, the Min PWM is 1220 and Motor start PWM is 1220...
I'm set the start voltage to 3 V (max ?) and the start align voltage to 2.4 V. Now it's better , but not solved. In AQ misc. settings, the Min PWM is 1220 and Motor start PWM is 1220...
Greetings from Germany - Ralf
- Luxar
- Posts: 53
- Joined: Mon Dec 30, 2013 12:20 pm
Re: Motor / Propeller Problem
by aBUGSworstnightmare » Mon Dec 07, 2015 5:34 pm
- aBUGSworstnightmare
- Posts: 1460
- Joined: Fri Jun 22, 2012 5:24 pm
Motor / Propeller Problem
by Luxar » Mon Dec 07, 2015 8:50 pm
Thanks for helping
What Is your suggestion for Advance ?
I'll test your suggestions tomorrow if am back from work
What Is your suggestion for Advance ?
I'll test your suggestions tomorrow if am back from work
Greetings from Germany - Ralf
- Luxar
- Posts: 53
- Joined: Mon Dec 30, 2013 12:20 pm
Re: Motor / Propeller Problem
by aBUGSworstnightmare » Tue Dec 08, 2015 6:57 am
- aBUGSworstnightmare
- Posts: 1460
- Joined: Fri Jun 22, 2012 5:24 pm
Motor / Propeller Problem
by Luxar » Tue Dec 08, 2015 7:26 pm
I found a solution for me that work, thanks for help : 
: Greetings from Germany - Ralf
- Luxar
- Posts: 53
- Joined: Mon Dec 30, 2013 12:20 pm
Re: Motor / Propeller Problem
by Luxar » Mon Dec 14, 2015 12:33 pm
Only a Short success...
The motor reach only 4200 rpm later in run, only if the calibration current is set to 30A. According on ecalc website, the motor draws only 18A at full power on 3S...if am run the calibration with this 18/20 A, the motor runs later only till 3500 rpm...and Hoover throttle is 3000/3100 rpm...
Someone ideas....
The motor reach only 4200 rpm later in run, only if the calibration current is set to 30A. According on ecalc website, the motor draws only 18A at full power on 3S...if am run the calibration with this 18/20 A, the motor runs later only till 3500 rpm...and Hoover throttle is 3000/3100 rpm...
Someone ideas....
Greetings from Germany - Ralf
- Luxar
- Posts: 53
- Joined: Mon Dec 30, 2013 12:20 pm
Re: Motor / Propeller Problem
by aBUGSworstnightmare » Mon Dec 14, 2015 1:21 pm
- aBUGSworstnightmare
- Posts: 1460
- Joined: Fri Jun 22, 2012 5:24 pm
Re: Motor / Propeller Problem
by Luxar » Mon Dec 14, 2015 8:22 pm
I test various settings of timing/switch freaq./start_voltage and so on....nothing helps...only till 4100-4200 rpm 
Am set all Parameters to default, then change some as needed and run the calibration....one result in the esc32.txt attached
Tomorrow i solder a simple BLHeli ESC to the motor for test,if it possible to run the motor higher with it.
Am set all Parameters to default, then change some as needed and run the calibration....one result in the esc32.txt attached
Tomorrow i solder a simple BLHeli ESC to the motor for test,if it possible to run the motor higher with it.
- Attachments
-
esc32.txt- (911 Bytes) Downloaded 932 times
Greetings from Germany - Ralf
- Luxar
- Posts: 53
- Joined: Mon Dec 30, 2013 12:20 pm
Re: Motor / Propeller Problem
by JussiH » Tue Dec 15, 2015 11:53 am
Try and increase START_VOLTAGE and START_CURRENT
Usually when a motor fails to start, it is because the starting voltage and current is set too low.
Usually when a motor fails to start, it is because the starting voltage and current is set too low.
- JussiH
- Posts: 2103
- Joined: Thu Jun 21, 2012 9:25 pm
31 posts
• Page 2 of 4 • 1, 2, 3, 4
Who is online
Users browsing this forum: No registered users and 5 guests