Page 1 of 1
Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Tue Nov 27, 2012 9:54 pm
by Jessestr
Hello
I am doing test calibrations on my computer and I want to check the MAE of step 4a.. In the wiki it's about 0.11481 on only 2 loops (MAE).
Mine is 275 loops in about 10 minutes and it is at 0.256275.. Every step a drop of 3 +- Sometimes bigger drops.
Now I'm typing another line and I'm at 325 loops and MAE : 0.256174 so it's going down well.. But it won't reach the same as in the wiki ...
Is this normal?
Jesse
Re: Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Tue Nov 27, 2012 10:35 pm
by Max
Yea, the MAE is always relative, so specific examples don't apply. As long as it's dropping steadily and not doing funky things like jumping around a lot, you should be fine. My first board/calibration had lower MAEs than my 2nd by about a factor of 0.1 (but 2nd flies fine too
).
-Max
Re: Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Tue Nov 27, 2012 11:37 pm
by Jessestr
Thanks. At 2430 now and MAE: 0.251821 and still every step is now going down by 2 and not anymore 3.
So, don't know if I have to wait until it's really done. Since the wiki says about 500-2000 samples.
Think my dance was quite well so don't have any bad data.. Could you check my other topic from the dynamic calibs logs?
Thanks
Re: Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Wed Nov 28, 2012 12:38 am
by Max
Re: Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Wed Nov 28, 2012 1:15 am
by Jessestr
Thanks.
4538 loops - MAE: 0.248672
Dropping with 0.000001 and about every 10 steps it drops with 0.000002
Re: Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Wed Nov 28, 2012 1:56 am
by Jessestr
Seriously.. Just aborted. Saved params to file and then started again.
Went from 0.247826 to 0.175984 and dropping with 0.000004 now.. So think it's good for a while again.
Went to step 4b sim3 - acc and the last three numbers are swinging with like 0.000300 / loop up and down..
Re: Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Wed Nov 28, 2012 9:44 am
by Jessestr
I need some help... Shall I redo my calibso? The swing stops after a while and then it goes steadily down.
MAE is now: 0.173406 but the ACC does weird sometimes.
Re: Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Thu Nov 29, 2012 10:44 am
by JussiH
Re: Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Thu Nov 29, 2012 11:47 am
by Jessestr
Thanks. the swings stop after some time. Will have to do the dance again anyways when adding my Video Downlink & Camera gear. Calculations were done in about 7 hours.
Re: Dynamic Calibration - Step 4A Sim3 Gyro MAE ~
Posted:
Wed Jul 09, 2014 11:27 am
by Dju
Hi everyone,
my MAE in step 4a and 4b begins at 4.2, it's strange no ?
the result seems to be good during few loops, and after that they act in really weird way:
0.741440 0.273468 2.771778 0.000000 0.000000 = 3.786686
[HLoops: 682
#define IMU_GYO_SCAL_X -5900.544612325033 // 8944.950111444725 +106.881028922500
#define IMU_GYO_SCAL_Y -6050.408275024172 // 58972.284551643650 -703.289438709729
#define IMU_GYO_SCAL_Z -88784.184049529023 // 9315722119.735080700000 -597394.759127230500
#define IMU_GYO_ALGN_XY +862263.787741126960 // 634843878.428503160000 -113894.974727822820
#define IMU_GYO_ALGN_XZ +4001.867336844128 // 51085.411866201895 -62.084803471233
#define IMU_GYO_ALGN_YX +367852.266788441160 // 1446245671.579250800000 +152451.169690260020
#define IMU_GYO_ALGN_YZ +17187492582100.691000000000 // 114599560903686510000000.000000000000 +707146458765.958980000000
#define IMU_GYO_ALGN_ZX -0.018716088987 // 0.000001802061 +0.000000000606
#define IMU_GYO_ALGN_ZY +0.173243641574 // 0.000779520372 +0.000000039461