SDIO WRITE error != SD_OK

Radio, Telemetry, FTDI/USB, ESCs, Motors, etc.

Re: SDIO WRITE error != SD_OK

Postby aBUGSworstnightmare » Thu Sep 11, 2014 1:45 pm

Hi,

Go to www.sdcard.org, click downloads and get the SD Formatter 4.0.

Format your card with the tool and check again.
Also check the card slot itself.

Joerg
aBUGSworstnightmare
 
Posts: 1460
Joined: Fri Jun 22, 2012 5:24 pm

Re: SDIO WRITE error != SD_OK

Postby Jenne » Thu Sep 11, 2014 7:14 pm

Hi,

thanks for your comments, but cleaning the card holder is a bit complicated, since it is almost completely closed. I tried it, but I don't think, this was very successfull.

today, I bought 2 additional SD cards, but I still have the SDIO error.
Now, I tested the following cards:
- Samsung Pro 8GB
- Transcend Premium 300x 8GB
- SanDisk Extreme 16GB (no "Plus", I couldn't get a 8GB card)

the Cards were formatted to FAT32, I also tested the SanDisk Card with 4GB Fat16.
Are these cards still not suitable?

Jens
Jenne
 
Posts: 20
Joined: Tue Aug 12, 2014 2:20 pm

Re: SDIO WRITE error != SD_OK

Postby Jenne » Thu Sep 11, 2014 8:16 pm

Hi,

I used the SDformatter-tool to format the cards.
I still have the SDIO-error message :-(

And when I try to write to th card I get the following:
(MAV 098) FAILURE: Temporarily rejected CMD: 245
(MAV 098) config: Error writing parameters to file.

Concerning the check of the card-holder. What can I do?. For me, it looks fine (no broken or deformed contacts, I know the "bending-mod").

Is there something else I can do?

Thanks for helping,
Jens
Jenne
 
Posts: 20
Joined: Tue Aug 12, 2014 2:20 pm

Re: SDIO WRITE error != SD_OK

Postby Jenne » Fri Sep 12, 2014 10:50 am

Hi,

I ordered an additional 8GB Extreme Pro and I will get it next week. However, I don't think this will solve my problem.

I guess, my AQ is broken. Nevertheless, I would be happy if somebody could give me any additional information or help concerning this error. For example, I would like to know if this is an already known problem? Can it be repared or is the AQ waste?

Thanks from a very dissapointed newbe,
Jens
Jenne
 
Posts: 20
Joined: Tue Aug 12, 2014 2:20 pm

Re: SDIO WRITE error != SD_OK

Postby bn999 » Fri Sep 12, 2014 2:02 pm

If all cards you try exhibit the same behavior, then I would guess that there is something wrong with your AQ board. The SDIO (uSD) interface is very simple and has no active parts so it could only be the uSD card holder, the MCU or the wiring (perhaps solder bridge) in between. If you have a magnifying glass, take a close look at the MCU's pins and look for a solder bridge between any of its pins. If there are none, then I'd next try replacing the uSD cage - not a job for an inexperienced solderer. If that does not work, then it has to be the MCU - but that is unlikely.
bn999
 
Posts: 1559
Joined: Thu Jun 21, 2012 11:40 pm

Re: SDIO WRITE error != SD_OK

Postby JussiH » Fri Sep 12, 2014 3:00 pm

You can send the board into here and I will take a look and repair it. If it was bought recently from a official dealer, then a uSD failure is covered by warranty. Send me a PM to get a RMA case going.

Jussi
JussiH
 
Posts: 2103
Joined: Thu Jun 21, 2012 9:25 pm

Re: SDIO WRITE error != SD_OK

Postby Jenne » Fri Sep 12, 2014 3:12 pm

JussiH and bn999,

thanks for your answers.
It gets even worse now. Now, only the red LED is still on. The others has gone and I cannot connect to the computer. What do you think. Can I try to flash it again.

Yes, I think I have to give the board to someone for repair. I bought the AQ last week here in the forum thus I don't have a dealer. Main reason to buy a used one was that I wanted to have the DIMU already installed, the pins connected and the firmware flashed.

I will be gone for the next 2 days, but I will contact you afterwards.

Jens
Jenne
 
Posts: 20
Joined: Tue Aug 12, 2014 2:20 pm

Re: SDIO WRITE error != SD_OK

Postby JussiH » Fri Sep 12, 2014 10:15 pm

Of course buying a used and retrofitted board from someone you dont know, is gonna run you the risk of problems like this.

However, in normal cases, your problem should be very repairable and I am willing to take a look at it and give you a repair quote on it. If its only the SD slot, then its not a big deal to repair or replace and it wont cost much.
JussiH
 
Posts: 2103
Joined: Thu Jun 21, 2012 9:25 pm

Re: SDIO WRITE error != SD_OK

Postby DUKE40 » Sat Sep 13, 2014 7:48 am

Jenne wrote:JussiH and bn999,

thanks for your answers.
It gets even worse now. Now, only the red LED is still on. The others has gone and I cannot connect to the computer. What do you think. Can I try to flash it again.

Yes, I think I have to give the board to someone for repair. I bought the AQ last week here in the forum thus I don't have a dealer. Main reason to buy a used one was that I wanted to have the DIMU already installed, the pins connected and the firmware flashed.

I will be gone for the next 2 days, but I will contact you afterwards.

Jens


Hi Jenne,

you could have got this with a new board, I got mine from Jussi with everything soldered on it, I only had to flash the latest firmware which is really a piece of cake.
Just need QGC and a FTDI adapter, which you always need to configure you AQ to your use.
Best regards,
Image
Spacewalk 550, MT2216-11, SimonK 20A ESC, AQ6 DIMU, 10x5" CF, SJ4000
CamCruiser, MN3510, ESC32, AQ6 DIMU, 12x4" CF, SimpleBGC, GoPro Hero 3 BE
DUKE40
 
Posts: 364
Joined: Tue Mar 26, 2013 9:49 pm

Re: SDIO WRITE error != SD_OK

Postby JussiH » Tue Oct 07, 2014 12:41 am

I fixed your board.

The problem was very likey due a badly soldered DIMU and possibly also a cold joint or hairline short on the main MCU.

The board now works properly after cleaning and reflowing of solder joints on the DIMU and Main MCU.

The repair is free of charge. But I´ll ask you to pay return shipping on it. Send me a PM!

Jussi
JussiH
 
Posts: 2103
Joined: Thu Jun 21, 2012 9:25 pm

PreviousNext

Return to Connections

Who is online

Users browsing this forum: No registered users and 5 guests

cron