Page 3 of 3
Re: AutoQuad & Spektrum telemetry
Posted:
Tue Jun 24, 2014 7:25 pm
by kinderkram
Good find, Joerg!
Does it work if you power the transmitter after powering the AQ?
Sounds like the Tx is awaiting some input from the module when booting...
Re: AutoQuad & Spektrum telemetry
Posted:
Wed Jun 25, 2014 12:32 pm
by joebar.rc
First post updated with the location of the arduino package, a wiring diagram, instructions and sample screens
- ProMicro_con_spektrum.png (142.54 KiB) Viewed 30297 times
Re: AutoQuad & Spektrum telemetry
Posted:
Sun Jul 06, 2014 1:00 pm
by Fridi71
Hallo,
I just ask here in the forum.
I search a telemetry between ArduPilot and Spectrum DX9.
I have now downloaded the software and transfer it to my Arduino micro.
The Micro according to the plan and connect the RX LED also flashes fine in time.
But really I do not see much on my DX9.
Tried various settings in the spark, no success.
Probably the code of Mavlink Autoquad after ArduPilot must be changed.
Who can provide support?
Re: AutoQuad & Spektrum telemetry
Posted:
Sun Jul 13, 2014 8:48 am
by aBUGSworstnightmare
Re: AutoQuad & Spektrum telemetry
Posted:
Thu Dec 18, 2014 8:30 pm
by Fridi71
Hallo,
I have the telemetry now running.
Only Alt is not displayed.
The value is briefly displayed in the DX9 and then back to zero.
If I set a fixed value in this code is also displayed only once.
Can someone help of a case.
Greeting Fridi
Re: AutoQuad & Spektrum telemetry
Posted:
Mon Jan 04, 2016 6:38 am
by jtcrowder49
Hello all, and thank you for the wonderful forum here. I have had auto quad for some time now and I just came across this great telemetry mod. I have been trying to compile the sketch for use on my board now for two days and it has been throwing the same error. I even re-downloaded my libraries. Can someone please help me with this? the error message is this...
In file included from /Users/crowderjake/Downloads/Mav2Telem_v1/Mav2Telem/Mav2Telem.ino:70:0:
/Users/crowderjake/Documents/Arduino/libraries/FastSerial/FastSerial.h:47:3: error: #error Must include FastSerial.h before the Arduino serial driver is defined.
# error Must include FastSerial.h before the Arduino serial driver is defined.
^
exit status 1
Error compiling.
I've been using arduino for some time but nothing I seem to do works. I even followed the comments in the code.
Thanks for the help!
-Jake
Re: AutoQuad & Spektrum telemetry
Posted:
Mon Jan 04, 2016 10:53 am
by Simson
Maybe someone can just post the hex file....then you don't need to investigate the problems with the Arduino IDE.
With X Loader you can flash the hex code directly to the Arduino.
Re: AutoQuad & Spektrum telemetry
Posted:
Mon Jan 04, 2016 4:53 pm
by jtcrowder49
Re: AutoQuad & Spektrum telemetry
Posted:
Mon Feb 29, 2016 3:59 pm
by aBUGSworstnightmare
Spektrum finally decided to release the documentation of their telemetry interface, so no more reverse engineering
Any Kunz posted it on RCgroups, i.e. here
http://www.rcgroups.com/forums/showpost ... count=1128So, let me add the manual to this thread as well
- Spektrum Telemetry Rev E.pdf
- Spektrum telemetry manual
- (338.21 KiB) Downloaded 1920 times
aBUGSworstnightmare