Re: OSD for AQ
Posted: Thu Jan 22, 2015 12:23 pmup to 500mA on single output
Hi all.
This OSD looks very promising. How to get one for testing?
AutoQuad Forum
AutoQuad :: Autonomous Multi Rotor Vehicle Controller
http://forum.autoquad.org/
OSD for AQ
Page 6 of 8
Posted: Thu Jan 22, 2015 12:23 pmRe: OSD for AQ
Posted: Tue Apr 21, 2015 10:41 pmRe: OSD for AQ
Posted: Tue Apr 28, 2015 6:00 pmGuys !
What about videos ? tests ? opinions ?
What about videos ? tests ? opinions ?
Re: OSD for AQ
Posted: Tue Apr 28, 2015 6:17 pmHi Bluuu,
I was not able to test it in flight up to know, due to several technical issues with my Hexa, but the tests on the ground look promising.
For a small hexa like mine, the board could be smaller, it was quite a work to fit it into the frame.
Some improvements, I would really love are, but are not a must:
vHacc and vHacc to be displayed
an indication in which direction home is
As soon as I will get the hexa airborne, I will try to make a short video, the Recorder is already there, just needs to be connected to the goggles.
Will keep updated.
I was not able to test it in flight up to know, due to several technical issues with my Hexa, but the tests on the ground look promising.
For a small hexa like mine, the board could be smaller, it was quite a work to fit it into the frame.
Some improvements, I would really love are, but are not a must:
vHacc and vHacc to be displayed
an indication in which direction home is
As soon as I will get the hexa airborne, I will try to make a short video, the Recorder is already there, just needs to be connected to the goggles.
Will keep updated.
Re: OSD for AQ
Posted: Thu Jun 04, 2015 8:36 pmGuys, any update ?
Re: OSD for AQ
Posted: Wed Jun 10, 2015 7:25 pmHave same question. Project was died?
Re: OSD for AQ
Posted: Wed Jun 10, 2015 8:25 pmNo project has not died, but seems the testers are not really providing any feeedback, unfortunately including myself.
We are currently replacing the kitchen, meaning we have taken the old kitchen out and now the whole room is being made completely new, new walls, new floor, electricity is being remade, and so on, a lot of work and unfortunately no time for flying.
But it is on my ToDo list and hopefully soon I will find some time for it.
We are currently replacing the kitchen, meaning we have taken the old kitchen out and now the whole room is being made completely new, new walls, new floor, electricity is being remade, and so on, a lot of work and unfortunately no time for flying.
But it is on my ToDo list and hopefully soon I will find some time for it.
OSD for AQ
Posted: Fri Jun 12, 2015 5:16 pmI have an current sensor in my system, if it possible to display it / to change parameters of Current sensor in osd configurator.
And an extra checkbox in osd configurator , to display/hide the GPS coordinates separate in OSD.
The connectors are ok, but normal 3 pin connectors like servo connectors would be fine...am already solder the wires direct on board....no need of "special" 4 pin connectors...
And an extra checkbox in osd configurator , to display/hide the GPS coordinates separate in OSD.
The connectors are ok, but normal 3 pin connectors like servo connectors would be fine...am already solder the wires direct on board....no need of "special" 4 pin connectors...
Re: OSD for AQ
Posted: Sat Jul 04, 2015 10:19 pmHey, guys. How about progress? I can test this OSD and publicate videos, but how to get it?
Re: OSD for AQ
Posted: Mon Jul 20, 2015 12:17 amThis looks quite interesting. I'm curious what the beta testers have to say about it. Also, I'm interested in the code that the board runs. Would it be compatible with something like the MinumOSD? It looks like both use the same basic chips. For now, I'm going to run the code that KISSSYS published that works with Minum, but because this is more AQ specific I'd rather run this.