Hi AQler,
after setting up my AQ - flashing with FW 6.6.1 rev2 it first looked good but when it comes to try the first flying i have some problems with spinning some of the motors. Only the front left (Quad X) is spinng up then with more throttle the left back Motor spins up too, but both right motors does not spin. i configured the mixing table custom to use the Port 3 (left front), 10 (right front), 8 (right back) and 1 (left back) to keep the cables short.
After long trys in differnt ways i decided to flash the AQ new and now i always get the well know Message:
"Failed to get init ACK from device"
Com port is right, jumper is set, Flyduino FTDI connected right (new version).
I can connect to the AQ in non bootloader mode, i see my rc controls working fine, i can arm and disarm, see the horizon moving right - so connection seems to be fine - but if i try to write any change to the aq i get the warning:
"possible problem(s) exist:
MOT_FRAME
MOT_PWRD_01_P
MOT_PWRD_01_R
MOT_PWRD_01_T
MOT_PWRD_01_Y
MOT_PWRD_02_P
MOT_PWRD_02_R
MOT_PWRD_02_T
MOT_PWRD_02_Y
MOT_PWRD_03_P
MOT_PWRD_03_R
MOT_PWRD_03_T
MOT_PWRD_03_Y
MOT_PWRD_04_P
MOT_PWRD_04_R
MOT_PWRD_04_T
MOT_PWRD_04_Y
MOT_PWRD_05_P
MOT_PWRD_05_R
MOT_PWRD_05_T
MOT_PWRD_05_Y
MOT_PWRD_06_P
MOT_PWRD_06_R
MOT_PWRD_06_T
MOT_PWRD_06_Y
MOT_PWRD_07_P
MOT_PWRD_07_R
MOT_PWRD_07_T
MOT_PWRD_07_Y
MOT_PWRD_08_P
MOT_PWRD_08_R
MOT_PWRD_08_T
MOT_PWRD_08_Y
MOT_PWRD_09_P
MOT_PWRD_09_R
MOT_PWRD_09_T
MOT_PWRD_09_Y
MOT_PWRD_10_P
MOT_PWRD_10_R
MOT_PWRD_10_T
MOT_PWRD_10_Y
MOT_PWRD_11_P
MOT_PWRD_11_R
MOT_PWRD_11_T
MOT_PWRD_11_Y
MOT_PWRD_12_P
MOT_PWRD_12_R
MOT_PWRD_12_T
MOT_PWRD_12_Y
MOT_PWRD_13_P
MOT_PWRD_13_R
MOT_PWRD_13_T
MOT_PWRD_13_Y
MOT_PWRD_14_P
MOT_PWRD_14_R
MOT_PWRD_14_T
MOT_PWRD_14_Y
Do you wish to ignore this and continue saving?"
Additional i cant see the Version of the AQ FW in QGroundstation 1.3B or 1.2.1.
My Testsystem (QuadX) is flashed with FW 6.6.1 rev 2 and i use blheli ESCs with fully damped Mode (HK-10) with Suppo 2208 and RC is via PPM with old Graupner MX16 Hott and Thomas Scherrer LRS.
I think there is something wrong with the FW on the AQ but i cant flash it - any Advice is highly appreciated.
THX
Michael