TAROT 4006 620 kv - params needed

Info and Discussion about the ESC32 hardware and software

TAROT 4006 620 kv - params needed

Postby afernan » Tue May 24, 2016 4:15 pm

I'm using this motors with carbon propellers TM 1344 with QUATOS and EXC32V2.

They work well, with a very low vibration level (<1m/s2) but they do this "birdy" noise. Do any of you have some params set that works well?.

Attached the params I'm using

Angel
Attachments
esc32.txt.zip
(569 Bytes) Downloaded 94 times
afernan
 
Posts: 1214
Joined: Sat Jul 07, 2012 5:24 pm
Location: Madrid, Spain

Re: TAROT 4006 620 kv - params needed

Postby chschmid » Tue May 24, 2016 10:23 pm

I would have data for GRP 12x6 and T12x4 at 4s.

Cheers
Christof
chschmid
 
Posts: 1800
Joined: Wed Jul 11, 2012 7:41 pm
Location: Herrliberg, Switzerland

Re: TAROT 4006 620 kv - params needed

Postby afernan » Thu May 26, 2016 7:15 am

Hi Christoff:
yes, TM1240 propellers should be OK. Please, share the params you use.

Do you remember to get good performances? . I still have some "glitches" and not very smooth running with this motors. Nothing compared with the TMotor.

Regards
Angel
afernan
 
Posts: 1214
Joined: Sat Jul 07, 2012 5:24 pm
Location: Madrid, Spain

Re: TAROT 4006 620 kv - params needed

Postby aBUGSworstnightmare » Thu Jun 02, 2016 8:17 pm

afernan wrote:I'm using this motors with carbon propellers TM 1344 with QUATOS and EXC32V2.

They work well, with a very low vibration level (<1m/s2) but they do this "birdy" noise. Do any of you have some params set that works well?.

Attached the params I'm using

Angel


Is it the same noise as you can hear in the CamCruise videos? I'm using them with Graupner e-Prop. I have parameters and QUATOS data for this combination (for ESC32V2) - same as Christof since he made the measurements that time!

I'm absolutely satisfied with their performance.
aBUGSworstnightmare
 
Posts: 1460
Joined: Fri Jun 22, 2012 5:24 pm

Re: TAROT 4006 620 kv - params needed

Postby afernan » Thu Jun 02, 2016 10:40 pm

aBUGSworstnightmare wrote:
afernan wrote:I'm using this motors with carbon propellers TM 1344 with QUATOS and EXC32V2.

They work well, with a very low vibration level (<1m/s2) but they do this "birdy" noise. Do any of you have some params set that works well?.

Attached the params I'm using

Angel


Is it the same noise as you can hear in the CamCruise videos? I'm using them with Graupner e-Prop. I have parameters and QUATOS data for this combination (for ESC32V2) - same as Christof since he made the measurements that time!

I'm absolutely satisfied with their performance.

I using now the Christof params and work muchas muchas better. Still a bit of birdy noise but aceptable.
I changed to 1245 wood HQ propellers. They give better performances than 1345

Enviado desde mi Nexus 5 mediante Tapatalk
afernan
 
Posts: 1214
Joined: Sat Jul 07, 2012 5:24 pm
Location: Madrid, Spain


Return to ESC32

Who is online

Users browsing this forum: No registered users and 6 guests

cron