Page 6 of 7
Re: TK4 - Build
Posted:
Thu Feb 28, 2013 4:15 pm
by chschmid
Ok ThinMan, thats reasonable.
Right now I am using 16mm tubes.
When I build my next copter I will layout it for 22mm and get back to you. Maybe you will have them longterm tested by then.
Best
Christof
Re: TK4 - Build
Posted:
Thu Feb 28, 2013 5:41 pm
by ThinMan
All my life i learning many things, but with foreign languages i have big problems, it goes not in my head.
I`m a autodidact, but only in my language.
I`m need a german wiki, sorry. Or a helping human in my town.
ThinMan
Re: TK4 - Build
Posted:
Thu Feb 28, 2013 11:33 pm
by chschmid
Never mind, ThinMan
(Kein Problem. Ich habe Dir geschrieben, dass Deine Preisvorstellung vernünftig ist. Im Moment verwende ich 16mm Rohre. Mein Nächstes Projekt werde ich dann wohl in 22mm ausführen. Wenn es soweit ist, melde ich mich bei Dir. Bis dann hast Du ja die Verbinder sicher im Härtetest gehabt
. )
Gruss
Christof
Re: TK4 - Build
Posted:
Fri Mar 01, 2013 12:55 am
by ThinMan
Hallo!
Falls Du was mit 22 mm planst, denke bitte daran, das die Bohrlochabstände vorgegeben sind, sonst müßte ich die Steckverbindungen ja komplett neu konstruieren.
Ich habe ja zwei verschiedene, etwas längere für den Quadro und kürzere für den Y-Okto, dessen steckbare Arme (die äußeren) sind ja nur 270 mm lang. Passen aber 13er Props noch drauf. Für durchgehende Motorarme würde ich dann die längeren nehmen.
Gib bei shapeways thinkopter ein, ich lade immer mal wieder Teile zur Ergänzung hoch. Fragt halt ab und zu mal einer nach anderen Teilen, die mache ich ihm dann.
ThinMan
Re: TK4 - Build
Posted:
Thu Mar 07, 2013 7:00 pm
by ThinMan
Hello!
A new photo from the first 2 layers (one for the bottom, 1 cm) of foam for the motorarms in the case:
ThinMan
Re: TK4 - Build
Posted:
Sun Mar 10, 2013 4:58 pm
by ThinMan
Hello!
Here a photo from the other layers:
Under the core ist one lipo, on the gimbal mounted the CX730 E. Motorarms and landing gear are in the cover.
ThinMan
Re: TK4 - Build
Posted:
Tue Apr 16, 2013 7:26 pm
by ThinMan
Hello!
The Kopter Box is ready.
Quadro ThinKopter TK 4 (67 cm Motor zu Motor), Gimbal, CX 730 E, Spectrum DX10t
ThinMan
Re: TK4 - Build
Posted:
Sun Apr 21, 2013 4:32 pm
by ThinMan
Hello!
And here photos of the content of the box:
Details:
Thank you for your interest.
ThinMan
Re: TK4 - Build
Posted:
Sun Apr 21, 2013 5:55 pm
by kinderkram
Beautiful, well done, Thinman!
When will we get a chance to see your creation in action? I think you'll get some decent footage with the CX730.
Re: TK4 - Build
Posted:
Sun Apr 21, 2013 6:13 pm
by ThinMan
Hello!
Thank you, but i have many problems with the ESC 32 and the AQ (suddenly no arming), no video-downlink, no telemetrie, no LED`s (respectively no regulation for it).
I have many pieces here and no plan. My english is not better and this is the crux. I search a specialist for AQ in Berlin, also for the TKY 8 (Oktokopter).
Conclusion, it is a long way to fly.
Tomorrow, i make a new attempt. Now i am bugged out.
ThinMan